PTC Porcelain Tile Cutters
The solution to non-slip and easy start-up: Diamond ground tip geometry actually bites into tiles, eliminating wander and slip at the start of drilling. Each pack contains the same sized pro masonry bit to complete the drilling of supporting substrates to enable fixing installation.
PTC Carbide
| Product Description | Part Number |
|---|---|
| PTC Multi Pack - all sizes | CTCMP1 |
| 5.0mm - 3/16" PTC Drill | CTCP5.0 |
| 6.0mm - PTC Drill | CTCP6.0 |
| 6.5mm - 1/4" PTC Drill | CTCP6.5 |
| 7.0mm - 9/32" PTC Drill | CTCP7.0 |
| 8.0mm - 5/16" PTC Drill | CTCP8.0 |
| 10.0mm - 3/8" PTC Drill | CTCP10.0 |
| 6.0mm - PTC Drill - SDS Shank | CTCS6.0 |
| 6.5mm - 1/4" PTC Drill - SDS Shank | CTCS6.5 |
| 7.0mm - 9/32" PTC Drill - SDS Shank | CTCS7.0 |
| 8.0mm - 5/16" PTC Drill - SDS Shank | CTCS8.0 |
| 10.0mm - 3/8" PTC Drill - SDS Shank | CTCS10.0 |
| 5.0mm PTC Multi-Pack | CTCSET5.0 |
| 6.0mm PTC Multi-Pack | CTCSET6.0 |
| 6.5mm PTC Multi-Pack | CTCSET6.5 |
| 7.0mm PTC Multi-Pack | CTCSET7.0 |
| 8.0mm PTC Multi-Pack | CTCSET8.0 |
| 10.0mm PTC Multi-Pack | CTCSET10.0 |
The solution to durability and extended life: Thin wall, continuous diamond crowns for fast, efficient cutting and extended life. Not to be confused with some short life diamond grit alternatives.
PTC Diamond
| Product Description | Part Number |
|---|---|
| 5.0mm PTC Diamond Crown | PTC05.0CRM |
| 6.0mm PTC Diamond Crown | PTC06.0CRM |
| 6.5mm PTC Diamond Crown | PTC06.5CRM |
| 7.0mm PTC Diamond Crown | PTC07.0CRM |
| 8.0mm PTC Diamond Crown | PTC08.0CRM |
| 10.0mm PTC Diamond Crown | PTC10.0CRM |
| 13mm PTC Diamond Crown | PTC13CR |
| 19mm PTC Diamond Crown | PTC19CR |
| 26mm PTC Diamond Crown | PTC26CR |
| 36mm PTC Diamond Crown | PTC36CR |
| 44mm PTC Diamond Crown | PTC44CR |
| 58mm PTC2 Diamond Crown | PTC58CR |
| 80mm PTC2 Diamond Crown | PTC80CR |
| 117mm PTC2 Diamond Crown | PTC117CR |
Merchandising
| Product Description | Part Number |
|---|---|
| PTC Foam Display Set | PTCBOXDEAL1 |
| PTC Counter Display | PTCBOXDEAL4 |
Fein Drill
| Product Description | Part Number |
|---|---|
| Fein 638 Drilling Machine | PTCF638 |
A full range of application specific sets are available as well as sets containing popular sizes and necessary accessories.
PTC Diamond - Sets
| Product Description | Part Number |
|---|---|
| PTC Piping Kit | PTCSET2 |
| PTC Piping & Fixings Kit | PTCSET1 |
| PTC Complete Drilling Super Set | PTCSET4 |
| PTC Wash Basin Fixing Set | PTCWBFSET1 |
| PTC Starter Set - 10mm micro bore copper pipe | PTC13MMSET |
| PTC Starter Set - 15mm Copper Pipes | PTC15CPSET |
| PTC Starter Set - 22mm Copper Pipes | PTC22CPSET |
| PTC Starter Set - 32mm Waste Pipes | PTC32WPSET |
| PTC Starter Set - 40mm Waste Pipes | PTC40WPSET |
| PTC Starter Set - 52mm Waste Pipes | PTC52WPSET |
| PTC Starter Set - Shower Mixer Valves | PTCSMVSET |
| PTC Starter Set - Vents & Soil Pipes | PTCV&SPSET |
Frequently Asked Questions for PTC Carbide Drills
What speed should the drill bits be used at ?
The drill bits should be used at the optimum speed range of between 700 and 900 rpm. Drilling outside this speed range will reduce the number of holes achievable.
Do the drill bits need water cooling?
The drill bits need a constant flow of water at the tip through the entire drilling process. This is best achieved using an Armeg water feed kit (code:- PTCWFKIT).
How quickly should I be able to produce a hole through a porcelain tile?
A hole should be produced through a porcelain tile in seconds rather than minutes. Excessive drilling times are usually due to insufficient pressure being applied through the drilling process or incorrect speed setting on the power tool.
How much pressure should I apply whilst drilling?
Sufficient pressure should be applied to keep the drill bit progressing through the tile (signified by tile dust being visible in the cooling water). Insufficient pressure will result in premature wearing of the carbide tip.
How many holes can I expect to produce?
Typically in a grade 5 porcelain tile, 15-20 holes should be achievable. 50+ holes have been produced in lesser grades of porcelain. When the drill bits have been exhausted in porcelain they can still be used to drill softer tiles.
Why are there two drill bits in my plastic tube?
The drill bit with the red wax cover over the tip is the tile bit, the other is a professional quality masonry bit for producing the fixing hole behind the tile. Do NOT use the tile bit for drilling masonry!
What sizes are available in PTC carbide?
PTC carbide drill bits are available in 5mm, 6mm, 6.5mm, 7mm, 8mm and 10mm.
What other materials can PTC carbide be used in?
PTC carbide drill bits can also be used in Marble, Granite, Travertine, Natural Slate, Quarry Tiles, Ceramic Tiles, Natural Stone, Limestone, Rosemary Roof Tiles etc.
Movies
Click below for an online demonstration video of PTC Carbide
Click below for an online demonstration video of PTC Diamond - Large
Click below for an online demonstration video of PTC Diamond - Small
